Packs/Racks/Baskets

- Integrated top plate for quick-mount MTX 1.0, 2.0, and RX trunk bags - Integrated fender top - 6061-T6 alloy construction - 625g - 55lb weight capacity

Named after the Italian word for Brick, Mattone is a water-resistant, ultra-compact seat bag that attaches to the rails using the BOA Closure System.  Unique zipper design allows it to be accessed while on the bike, or to open like a book when removed from the bike for easy access. Mattone is for the cyclist looking to carry a spare tube, CO2, multi-tool, and some cash in a discreet, water-resistant package. Internal divider holds ID, credit card, or cash while also protecting your tube from your multi-tool! Seat bag users fall into two categories: Seat Roll aficionados and seat bag users. Traditionally, seat bags have been simple open spaces that allowed content to jangle about, making noise and rubbing against each other. Often times a spare tube was pulled out of a seat bag to reveal it was more full of holes than the tube being replaced due to friction against a house key or multi-tool. With Mattone, we designed a layout similar to a book, where the bag can fully open to hold the tube and CO2 cartridge on one side, separated by a padded ballistic nylon 'page' separating it from the other side where you can store an inflator head, multi-tool, contact lens case, etc. The 'page' also contains a slot for a credit card, ID, money, or house key. The unique off-center Aquaguard Zipper allows the case to completely open and lay flat when off the bike, while also allowing easy access to the multi-tool and money/card slots when on the bike without risk of spilling all the contents of the bag. A high-friction Hypalon strap with BOA Closure completes the package. Making more than 15x the power of Velcro, the BOA Closure uses a ratcheting mechanism that will not creep or loosen even under the most extreme vibration and impact. This ensures the Mattone will remain 'high and tight' under your saddle until you need to access it...no swinging, swaying, or rattling...ever. - Exterior—Sleek black finish with reflective graphics - Interior—Hi-contrast red material with separate ID, credit card, or money flap - Interior Volume—Holds one inner tube, one CO2 cartridge, one tire lever (all of these components are sold separately and are not included) - BOA Closure System with open guide release on Hypalon retaining strap - YKK Aquaguard zipper - Outside Dimensions: 13cm x 8.5cm x 5.5cm - Volume: Approximately .61 L - Strap Measurements: 27cm x 4.5cm

Seat Capsule Premio is our BOA-powered saddlebag option for those that prefer more structure and internal volume than what a seat roll has to offer. A high-strength thermoformed shell creates a modular structure with two internal dividers that help keep everything organized. The capsule is secured to the bike using the BOA Closure System, and features a Rail Guard for superior grip and protection of the saddle rails. The zipper is a YKK locking model that bisects the lower third of the bag. Our designer chose this low position to make it easier to access the bag while it's still attached to the saddle; a key difference between a seat bag and a seat roll. - High strength Thermoformed shell - Boa Closure System with Guide - Rail Guard protects and grips saddle rails - YKK Locking Zipper - NO Velcro to damage your seat post or inner short legs - 625cc Internal Volume

Weighing just 290 grams (including adapter), the fork pack offers approximately 4.1 liters of additional storage space for bike packing. With the help of the QLS adapter, this ultra-light bag with roll closure can be mounted on forks with eyelets or cage mounts intended for this purpose, as well as on forks without cage mounts, as long as the fork blades sport a constant diameter of 30mm to 42mm. Specifications: - Ultralight, waterproof bag (single pocket) with roll closure - The Fork-Pack is primarily designed for attachment to bicycle forks, but it can be mounted on non-tapered vertical tubes with a consistent diameter, e.g. Kick Style Scooters - Abrasion-resistant PU-coated nylon fabric - Allows additional luggage to be carried on bikes using the Quick-Lock S (QLS) adapter system - Adapter is compatible with forks with eyelets and tubes with constant diameter from 30 mm to 42 mm - The Quick-Lock S mounting bracket may be bolted directly to a fork with „braze-on“ eyelets or attached to vertical tubes using the supplied band-clamps - Ultra-fast installation, with one click the bag snaps in to place - The removal is just as fast, simply move the release lever and pull the bag upwards - The robust Quick-Lock S mounting plate remains mounted to the bicycle - Low profile locking elements ensure snag-free use - Internal stiffener - Reflective ORTLIEB logo - Maximum load 3kg / 6.6lbs

Whether you're heading to the beach, riding to the grocery store, or just cruisin' around, Nantucket's Surfside Rear Wire Pannier Basket will get you and all your goodies there in colorful style. This cute Pannier Basket sports mesh wire construction for durability and attaches to the rear rack with two metal hooks, making it the perfect errand-running accessory.

If fashion is your bag, this bag is for you. Carry all of your commute essentials. Easily attach to your rear rack so that you, your laptop and lunch make it to work on time. Product details - Fits 15 inch laptop - Comes with Velcro straps for rear racks - Upgrade to MIK compatibility with MIK adapter plate (600928)

This basket is as sweet as honey. It's perfect for holding all your things, large and small. Easily attach and remove this quick release basket from your headset for added functionality and fun. You have things. We have things to hold those things. - Quick release bracket included - Proprietary Electra design - Honeycomb patterned stamp - Quick release unit mounts to handlebars - Powder coated steel - Carries up to 5kg (11lb) - Dimensions: 34cm (l) x 23cm (w) x 27.5cm (h) - Attachment: Quick Release - Includes hardware: Yes - Material: Steel - Weight: 1g

A convenient all-in-one pack containing useful tire-change essentials. Flats happen. Make sure you're prepared with a Bontrager Flat Pack. Featuring the storage, inflation, and tire removal equipment you need to handle an emergency flat repair, this purchase also includes a coupon for a free Bontrager tube so you can get the right size for your bike and tires. Product details - Kit features everything you need to quickly fix a flat, including the seat pack - Includes Pro Small seat pack (non-QC) for quick and easy on-bike storage - Contents include: mini pump, three tire levers, and patch kit - Also includes coupon for a FREE Standard Bontrager Presta or Schrader inner tube

Bontrager's Interchange Handlebar Basket is perfect for the farmer's market or carrying your books to class. It adds a touch of class and convenience to every bike. Plus, it fits all handlebars, goes on and off in a breeze, features sturdy wire construction and has a built-in carrying handle, too.

The Reggie 2 Drybag Pannier is a great companion on any bicycle ride to haul just about anything you want! Fully waterproof, the Reggie 2 Bike Drybag is a roll-top closer to keep out all water and is made with durable and puncture-proof water repellent material. It also comes with a shoulder strap with different carrying positions as well as an inside pocket for easy access to small items. - Fits most rear racks with strong plastic clips and a bungee net for tension on the rack - Interior pocket for storage of small items - Made from heavy-duty PVC Tarpaulin - Shoulder strap with multiple carrying positions - Reflective accents - Dimensions: 13 x 6 x 11 inches - 15 lbs. capacity - 850 cubic inches

Gear Bag 15

The HIP PACK CAPTURE 7L is EVOC's top-notch hip carry solution for sports photographers, offering compact, fast access to camera and perfect carrying comfort even in extreme sport scenarios. - Low-profile back system that fits more snugly to the back - AIRFLOW CONTACT SYSTEM for perfect back ventilation - Freely configurable camera compartment - The camera can be accessed easily and swiftly - Ergonomically optimized, adjustable hip belt system with quick access hip pockets - Usefully positioned compartments for small items - Carrying comfort assured through the easy adjustment of the gap between back and pack using the VENTI FLAP system - Integral rain cover and belt system for holding a tripod - The main padded camera compartment is protected by individually adjustable compartment dividers

Very handy pouch to carry your basic necessities on short loops. The best solution when you want to ride with the feeling of not carrying anything and still feel safe, having your phone, a tool, and some snacks well positioned on your hip. - AIR PAD SYSTEM offers great carrying comfort - 1L main compartment - 2 HIP BELT POUCHES for smaller items - 2 NUTRITION COMPARTMENTS, easy to reach

- Bottle holder - Tool compartment - Mobile phone pocket - Nutrition compartment - Key Holder - Airo Flex - Material: n100d Shadow Box, mesh - Volume: 1.5l - Size: 15 x 30 x 4cm - Weight: 220g (incl. drink bottle 280g)

- Bottle holder - Tool compartment - Mobile phone pocket - Nutrition compartment - Key Holder - Airo Flex - Material: n100d Shadow Box, mesh - Volume: 1.5l - Size: 15 x 30 x 4cm - Weight: 220g (incl. drink bottle 280g)

Hands-on top load backpack for your daily business. - Top load to main compartment - Padded notebook compartment - Organizer compartment

- Airo Flex hip belt and Air Pad System for ideal carrying comfort - Perfect pocket management-a place for everything - Elastic Mesh pockets with velcro fastening in the back & on left hip - Zippable pocket on right hip - Loop for mini-pump or CO2 cartridge & inflator - Material: N 210D Ripstop HD, PU Coated, 3D Air Mesh, Airo Flex - Volume: 0.8L - Size: 25 x 13 x 2cm (9.8 x 5.1 x 0.8") - Weight: 180g (0.4lbs)

Airo Flex hip belt and Air Pad System for ideal carrying comfort. - Perfect pocket management-a place for everything - Elastic Mesh pockets with velcro fastening in the back & on left hip - Zippable pocket on right hip - Loop for mini-pump or CO2 cartridge & inflator - Material: N 210D Ripstop HD, PU Coated, 3D Air Mesh, Airo Flex - Volume: 0.8L - Size: 25 x 13 x 2cm (9.8 x 5.1 x 0.8") - Weight: 180g (0.4lbs)

Versatile mountain bike backpack with outstanding carrying comfort and intelligent pocket management. - Most versatile entry-level riding backpack - Technical, well-ventilated carrying system with extra-wide hip belt - Superior comfort, well-climatized AIR-PAD back padding - Internal tool compartment with organizer functionality - Exterior transport flap for your bike helmet - Compatible with hydration bladders up to 3 liters - Volume: 12L

Versatile mountain bike backpack with outstanding carrying comfort and intelligent pocket management. - Most versatile entry-level riding backpack - Technical, well-ventilated carrying system with extra-wide hip belt - Superior comfort, well-climatized AIR-PAD back padding - Internal tool compartment with organizer functionality - Exterior transport flap for your bike helmet - Compatible with hydration bladders up to 3 liters - Volume: 16L

Versatile mountain bike backpack with outstanding carrying comfort and intelligent pocket management. - Most versatile entry-level riding backpack - Technical, well-ventilated carrying system with extra-wide hip belt - Superior comfort, well-climatized AIR-PAD back padding - Internal tool compartment with organizer functionality - Exterior transport flap for your bike helmet - Compatible with hydration bladders up to 3 liters - Volume: 8L

Versatile mountain bike backpack with outstanding carrying comfort and intelligent pocket management. - Most versatile entry-level riding backpack - Technical, well-ventilated carrying system with extra-wide hip belt - Superior comfort, well-climatized AIR-PAD back padding - Superior pocket management - Internal tool compartment with organizer functionality - Exterior transport flap for your bike helmet - Compatible with hydration bladders up to 3 liters - Volume: 8L

EVOC's Seat Pack Boa makes for useful extra storage on your bike; and it doesn't affect your riding, even when it gets rugged! This is an on-bike storage option that offers all the familiar top quality and functionality that EVOC is known for. - Adjustable capacity due to roll-top closure - Dropper post compatible - Soft TPE seatpost protection - Flexible main compartment closure that adjusts to bag size - Boa Fit System for easy and secure fixation - 100% waterproof

Seat Pack WP

• Made in U.S.A. (Maysville, KY) • Shallow baskets carry notebooks, boxes or other articles that lie flat • Dimensions: 18 x 13 x 6 inches; the basket tapers to 15.75 x 10.5 inches at the bottom • Extended handlebar clamps fit 7/8" and 1"diameter handlebars, and 1 3/4" apart to offer clearance for shift and brake cables • Baskets have 2-piece legs which extend from 14 inches to 22 inches and mount to either the axle or fork eyelets on bikes with quick release front hubs • 1392 has a Zinc plated finish and 1392GB has a Black Powder Coat Finish • Complete basket with fittings weighs 2.6 lbs.

The Giant Delivery basket is one of the most enduring and iconic products in Wald's catalog. Popular among messengers and paperboys (feel free to ask your father or grandfather about this noble profession), this basket is designed to carry large loads thanks to its stout legs, cargo bands, and heavy-duty handlebar clamps. - Made in U.S.A. (Maysville, KY) - Great for delivery, industrial bikes and hauling large loads - Reinforcement bands add extra strength - this basket is built for rugged use - Dimensions: 21 x 15 x 9 inches; the basket tapers to 18.25 x 12.25 at the bottom - Extended handlebar clamps allow greater clearance for shift and brake cables. They are 3 5/8" apart and fit 7/8", 1" and 31.8mm diameter handlebars - Legs extend from approx. 14 1/2 inches to 23 inches and have two mounting holes for mounting to either the axle or fork eyelets for bikes with quick release front hubs - 157B has a Zinc plated finish and 157GB has a Black Powder Coat Finish - Complete basket with fittings weighs 7.8 lbs.

This versatile basket is the most adaptable front basket Wald offers. - Made in U.S.A. (Maysville, KY) - Deep basket that is sized for a grocery sack - Dimensions: 14.5 x 9.5 x 9 inches; basket tapers to 12.25 x 7 inches - Extended handlebar clamps fit 7/8" and 1" diameter handlebars - Two-piece adjustable legs extend from approx. 14 inches to 22 inches and mount to either the front axle or fork eyelets for bikes with quick release front hubs - Available in gloss black (198GB) or white (198WH) Powder Coat Finish - Complete basket weighs 3 lbs.

- Made in U.S.A. (Maysville, KY) - Dimensions: 20.5 x 13 inches - Extended handlebar clamps are 2" apart, allow greater clearance for shift and brake cables, and fit 7/8", 1", and 1 1/4" diameter handlebars - Legs extend from 13 3/4" to 21 1/4" and have two mounting holes for mounting to either the axle or fork eyelets for bikes with quick release front hubs - Powder Coat Finish - Complete rack with fittings weighs 6.0 lbs.

This front basket system uses a bolt-on handlebar mount to allow for quick and easy removal of the basket itself. - Extended handlebar clamps allow greater clearance for shift and brake cables - Requires 3.5" of handlebar clearance for mount - Fits 7/8" to 31.8mm handlebars - Made in USA - Dimensions: 11.75 x 8 x 9"

Available in white (3339WH) and gloss black (3339GB) powder coat finishes - Made in U.S.A. (Maysville, KY) - Dimensions: 14.5 x 9.5 x 9 inches (1.25-inch rail on all sides - Two-piece adjustable legs extend from 14" to 22" and mount to either front axle or fork eyelets on bikes with quick release front hubs - Extended handlebar clamps allow greater clearance for shift and brake cables - Handlebar clamps are enlarged to fit 1 1/4", 1" or 7/8" OD handlebars - Rack is furnished with metric fasteners - Combo comes with a Wald 3133 quick release basket (dimensions: 14.5 x 9.5 x 9 inches; tapering to 12.25 x 7 inches) - Basket nests in the rack and locks into place - Lift the handle to release the basket and take it with you - Complete rack and basket combo weighs 4.8 lbs. each

Wald's medium size twin rear carrier basket is a durable way to carry heavier loads. With mounting points at both the seat stays and near the rear axle, you can haul more groceries, gear, or anything else you need to with less impact on your bicycle's handling. By placing the bulk of your load around the rear wheel, you increase your bicycle's stability. This allows you to carry 1-2 small grocery bags in each side basket with greater confidence and ease. - Made in U.S.A. (Maysville, KY) - These are 1-piece twin carrier baskets designed to fit on rear of the bicycle - Dimensions: 6.5 x 13.5 x 10 inches; tapers to 4.5 x 11.5 inches at the bottom - Rack is 5" by 13" long - Baskets can be mounted to frame eyelets or use the supplied mounting bracket - Legs have two axle mounting holes and one small hole to mount to the eyelet - 520 has a Zinc Plated Finish; 520GB has a Black Powder Coat Finish - Complete basket with fittings weighs 5.3 lbs.

Wald's big boy rear twin carrier offers tremendous amounts of cargo capacity. The 535 Twin Rear Carrier Basket lets you haul a reusable grocery bag in each basket with room to spare. With mounting points at both the seat stays and near the rear axle, you can haul more groceries, gear, or anything else you need to with less impact on your bicycle's handling. By placing the bulk of your load around the rear wheel, you increase your bicycle's stability. This allows you to carry your groceries, gear, computer, or backpack with greater comfort and ease. - Made in U.S.A. (Maysville, KY) - These are 1-piece twin carrier baskets designed to fit on rear of the bicycle - 7.5 x 18 x 11 inches; taper to 5 x 16 inches at the bottom - Rack is 5" x 16" long - Baskets can be mounted to frame eyelets or use the supplied mounting bracket - Legs have two axle mounting holes and one small hole to mount to the eyelet - 535 has a Zinc Plated Finish; 535GB has a Black Powder Coat Finish - Complete basket with fittings weighs 7.2 lbs.

Listen to your inner voice of adventure. Pack up your gear, get on your bike, and ride that epic trail. BackLoader is a large-capacity seat bag specially designed for bikepackers providing a streamlined way to carry gear without the need for a rear rack. Constructed of lightweight, highly water-resistant and durable materials, it mounts and removes quickly. The upgraded saddle mount system, in conjunction with compression straps, reduces the pendulum effect associated with large rear payloads, providing a comfortable ride for those long miles. An easy-access waterproof inner bag is included to keep contents completely dry. - Polyethylene / Nylon — Lightweight, durable, water repellent and stain resistant - Hook and loop fastener - Waterproof Rating: 10,000mm (waterproof inner bag) - Max Load: 5kg / 11lb - Safety light clip - Air release button

- Adventure ready saddle mounted removable drybag and holster system - Includes waterproof carry bag with air release valve to keep gear dry and compact - Bag easily slides in and out of holster without having to remove from bicycle - 15L measures 19.7

A quick mount handlebar drybag that can be used alone or mounted as an accessory bag atop our FrontLoader bag system. Featuring sonically welded seams, a roll top closure and weathertight zippers the BarLoader protects your valuable gear from dry dusty trails or rain when riding in wet conditions. CAPACITY - 6.5 L / 395 ci MATERIAL - TPU BAG ATTACHMENT - Quick release buckles and hook and loop fastener MAX LOAD CAPACITY - 3 kg / 6.61 lb ADDED FEATURES - Inner bag, Reflective printing, Shoulder strap SIZE - 31 x 25.8 x 8.9 cm / 12.2" x 10.2" x 3.5" WEIGHT - 276 g / 9.73 oz

A sturdy handlebar-mounted metal basket for shopping trips, quick jaunts around town. New QuickClick Handlebar Mount (Fixer 3e) allows installation on eBikes to make attachment and removal a breeze. - Capacity: 16L/975 Ci - Weight: 1370G/3.02 Lb - Size: 35x26x25cm/13.8”x10.2”x9.8” - Attachment: QuickClick Handlebar Mount (Fixer 3e) Fits 25.4mm and 31.8mm handlebars (shims included)

A clever handlebar bag that converts to a waist pack. Great for cameras, cell phones and other essentials you want close at hand. Rain cover included. - Divided main compartment, Two side zip pockets - Material: 1800 denier nylon - Max Load: 5kg / 11lb - Fully padded - Waist Belt, Carry handle, Rain cover, Yellow lining - QuickClick Handlebar Mount (Fixer 8) - Fits 25.4, 28.6 & 31.8mm handlebars - Size: 22 x 18 x 13cm / 8.7" x 7.1" x 5.1" - Weight: 334g / 11.78oz

Need more carrying capacity for running errands? Then check out Topeak's Front Basket. It easily attaches to you bike's handlebars and holds all your groceries or whatever else you pick up. And, the handle makes this basket extremely portable.

Pack all the gear you need and enjoy the freedom of bikepacking. FrontLoader is perfect for carrying light yet bulky items like sleeping bags, camping gear and spare clothing. Featuring a tough outer support harness and constructed of durable abrasion- and water-resistant materials, it's easily installed or removed with two straps, special spacer mounts, and quick-release buckles. A backside head tube strap attachment increases load stability. An 8-liter removable waterproof drybag keeps contents completely protected from wet weather and splashes while a built-in air release button purges unwanted air from the bag to effectively compress its contents. - Material: Polyethylene / EVA / Anti-slip texture PU leather - Durable, water repellent and stain resistant - Bag Attachment: Durable NBR rubber spacers and straps with quick-release buckles - Waterproof Rating: 10,000 mm (waterproof carry bag) - Max Load: 5kg / 11lb - Waterproof carry bag - Air release button Size - 33 x 28.7 x 5cm / 13" x 11.3" x 2" - 50 x 15 x 15cm / 19.7" X 5.9" x 5.9" (Waterproof Carry Bag) Weight - Bag: 325g / 11.46oz (Black), 319g / 11.25oz (Green) - Rubber Spacers: 132g / 4.65oz

Topeak's Fuel Tank mounts directly to your top tube, giving you quick and easy access to energy bars, your phone, wallet, tools or any small essential gear you need to keep close at hand while riding. The top opening, zipper accessed, main compartment keeps contents safe and secure.

- Integrated top plate for quick-mount MTX 1.0, 2.0, and RX trunk bags - Integrated fender top - 6061 T6 alloy construction - To be mounted on bikes with disc brakes - 625g - 55lb weight capacity

- This one size fits all tubular aluminum rear rack is designed for Fat bikes with disc brakes - Adjustable rack legs fit most 24" & 26" Fat bikes - Integrated side bar provides a lower pannier attachment for more cargo on top of the rack - The MTX 2.0 QuickTrack plate is compatible with any Topeak MTX trunk bag, MTX rear basket, and most other rack packs and panniers on the market - Not compatible with asymmetric rear stay design Fat bike frames - Includes extra-long mounting bracket and rear light mount - Max weight 55lbs - 16.9 x 13.4 x 11.4" - 2.79lbs

Topeak's MTX BeamRack is an awesome way to add touring capacity to bikes that won't accept conventional racks, such as dual-suspension mountain bikes. The quick-release mount clamps firmly to your seatpost and this rugged rack boasts durable aluminum construction capable of supporting up to 20-pounds with ease.

Need more carrying capacity for running errands? Then check out Topeak's Rear Basket. It easily attaches to a Topeak QuickTrack rear rack (sold separately) and holds groceries, work clothes and anything else you need to transport. And, its handle makes it extremely portable.

Topeak's MTX Trunk DryBag EX is perfect for commuting and running errands year round, in any weather. This dry bag is fabricated from tough, sonically welded and seam-sealed nylon with a roll-top closure making it fully waterproof. And, Topeak's ingenious MTX System makes it a snap to attach it to your Topeak MTX QuickTrack rack (sold separately). Added features include reflective highlights and shoulder strap making easy to carry when it's off your bike.

Topeak's MTX TrunkBag DX boasts an expandable main compartment to carry all the gear you need. It's built to last with rigid molded panels mated to 600-denier nylon. And, it's packed with handy features, such as a shoulder strap, carrying handle, taillight clip and top elastic straps. There are even reflective strips for safety. Plus, Topeak's ingenious MTX System makes it a snap to attach it to your Topeak MTX QuickTrack rack (sold separately). - Capacity 12.3 L / 750 ci - Compartments 1 Divided main compartmetn, two side zippered pockets, Multi-expanding top compartment - Added Features: Water bottle holder Shoulder strap Carrying handle Elastic top bungees 3M reflective strip Safety light clip Optional rain cover - Size (L x W x H): 36 x 25 x 21.5-29 cm / 14.2” x 9.8” x 8.5”~11.4” - Weight: 985 g / 2.17 lb

Large capacity MTX TrunkBag containing one main divided compartment with two expandable pannier side panels and rear water bottle holder. Topeak's unique construction process provides rigidity and water repellency. Compatible with all MTX QuickTrack racks with attached side frames. MTX Dual Side Frames are required when using side panniers on MTX BeamRacks. - Attachments 1 Divided main compartment, two side pockets with expandable panniers - Capacity: 16.6 L / 1010 ci - Added Features: Water bottle holder Shoulder strap Carrying handle Elastic top bungees 3M reflective strip Safety light clip Optional rain cover - Size (L x W x H): 36 x 25 x 21.5 cm / 14.2” x 9.8” x 8.5” - Weight: 1195 g / 2.63 lb

Epic offroad bike tours require you to bring all the essential tools and gear to keep from being stranded in the middle of nowhere. Designed to employ the unused space in your frame, MidLoader carries the heaviest items for your bike adventure. Constructed of lightweight, highly water-resistant and durable materials, it mounts and removes quickly with hook-and-loop fasteners. Two water-resistant zippered openings provide easy access to all your gear from either side. - Material: Polyethylene / nylon lightweight, durable, water repellent and stain resistant - Bag Attachment: Hook-and-loop fastener - Top Tube Diameter: Fits 45 - 66mm - Down Tube Diameter: Fits 38 - 70mm - Seat Tube Diameter: Fits 28 - 60mm Size - 3L: 37.5 x 12 x 6cm / 14.8" x 4.7" x 2.4" - 4.5L: 46 x 12 x 6cm / 18.1" x 4.7" x 2.4" - 6L: 54.5 x 13.5 x 6cm / 21.5" x 5.3" x 2.4" Weight - 3L: 277g / 9.77oz - 4.5L: 292g / 10.30oz - 6L: 337g / 11.89oz

Topeak's SideKick Wedge Pack features a unique, positive locking 2-piece mount that makes attaching and removing the pack a snap. Its unique side-opening design makes accessing your gear quick and easy and you'll have plenty of room for carrying tubes, a C02 pump, wallet, keys and whatever else you need. For low-light conditions, a 3M reflective strip adds safety and its semi-rigid construction makes the Wedge Pack durable and tough.

Specifically designed for up to an 8.5” tablet to provide ultimate protection against water and dirt. QuickClick handlebar mount (Fixer 9) is angle adjustable and holds the tablet close at hand.

A full featured medium capacity handlebar bag with a QuickClick mount and shoulder strap that makes it easy to take it with you. Fully padded, divided main compartment plus front zip and two side pockets keep gear organized. Perfect for extended touring, day trips and commuting. Rain cover included. - Clear map cover - Shoulder strap - Carry handle - Rain cover - 3M reflective strip, safety light clip (3M is a registered trademark of 3M Company) - Bag Attachment: QuickClick handlebar mount - Fits 25.4, 28.6 & 31.8mm handlebars - Compartments: Divided main compartment, front zip pocket, two side zip pockets, clear map pocket - Material: 1800 / 840 denier nylon - Max Load: 5kg / 11lb - Fully padded - Size: 25.5 x 23 x 18cm / 10" x 9.1" x 7.1" - Weight: 670g / 1.48lb

Our largest-capacity handlebar bag features a QuickClick mount and shoulder strap that makes it easy to take it with you. One large, fully padded, divided main compartment with zippered front and top pockets help keep gear organized. Perfect for extended touring, day trips and commuting. Rain cover included. - Clear map cover - Shoulder strap - Carry handle - Rain cover - 3M reflective strip, Safety light clip (3M is a registered trademark of 3M Company) - Bag Attachment: QuickClick Handlebar Mount - Fits 25.4, 28.6 & 31.8mm handlebars - Compartments: Divided main compartment, front zip pocket, clear map pocket - Material: 1800 / 840 denier nylon - Max Load: 5kg / 11lb - Fully padded - Size: 27 x 26.6 x 21.5cm / 10.6” x 10.5” x 8.5” - Weight: 1230g / 2.71lb

Topeak's Trolley Tote rear basket provides excellent versatility and convenience. Handy features include a telescoping handle and wheels which make the Trolley Tote perfect for shopping and running errands. It's made from tough plastic with an aluminum handle, and folds flat for storage. And, it's compatible with Topeak's QuickTrack rack system for easy on and off.

A sturdy steel rack which allows for mounting Thule Yepp Maxi Easyfit and Thule Yepp Nexxt Child Bike seats. Features - Compatible with most 26" city and hybrid wheeled bikes - Supports up to 35Kg/77 lbs

A sturdy steel rack which allows for mounting Thule Yepp Maxi Easyfit and Thule Yepp Nexxt Child Bike seats. Features - Compatible with most 28"/700c city and hybrid wheeled bikes - Supports up to 35Kg/77 lbs

Surly's Dummy Deck provides a light, durable platform for cargo bikes, built to Xtracycle's Longtail standard — including the Big Dummy, of course. The Dummy Deck is stamped from 4mm-thick aluminum, chosen for its strength, durability, and recyclability, and it bolts directly to Surly Dummy Rails to stiffen and stabilize the whole system (it's also compatible with Xtracycle V-racks by using Xtracycle's SuperHooks). It features cut-outs for routing straps and cordage, a mounting hole for a rear light bracket, accessory-mounting holes, and countersunk holes for SuperHook hardware.

Dummy Rails support Dummy Bags on your Big Dummy cargo bike, and Surly's Dummy Deck bolts directly to them, stiffening the whole system for a more stable load. Dummy Rails are made of light, strong aluminum and were designed in conjunction with the Dummy Deck and Dummy Bags; each component works best when used with the others. Like all Surly products, they've built in lots of useful details. For example, the deck-attachment bosses stick up from the rails to create space between the deck and rails, providing windows to route tie-down straps and cordage; and threaded bottle cage bosses located at the rear of each rail provide mounting locations for accessories: bottle cages of course, or lights, cameras, pumps, flags, horns, light saber scabbards, disco balls, spittoons, cornucopias, etc. Dummy Rails will work with cargo frames (including the Surly Big Dummy) built around Xtracycle's longtail standards.

The Surly Little Dummy Bag is a 15L sling-style bag designed to work with your standard rear rack and help you carry grocery bags, fishing poles, and other oddly shaped ephemera. Unlike traditional panniers that clip on and off real fast, we wanted a cargo solution that you could leave mounted to your bike when you're off playing laser tag. The idea is you just throw your backpack or whatever in there, turn the cranks awhile, and then pull out your gear when you've arrived. Quite slick. You can still scatter schoolbooks and loose cans of tuna inside the Little Dummy if you want, but the bag-within-a-bag method makes unpacking quicker. Use the system of daisy chains and One-Wrap straps to secure baguettes, flutes, and other stuff that might stick out. Cinch the side straps to further stabilize your load. And for extra credit, use your favorite Surly Whip Lash or Junk Strap to make your setup work the way you want. There's also a small zippered compartment inside the bag, if you're into pockets. Oh, and we should also probably mention that the bag's 1680D nylon main body and 400D nylon liner are bluesign Approved. So are the buckles and other hardware. That means the materials are sustainably produced to have the lowest possible impact on humanoids and our environment. Compatible with most standard rear racks, the Surly Little Dummy Bag is a sling-style bag designed to help riders haul big awkward items more easily. Secure your backpack, groceries, or camping gear inside the sling when it's time to ride. When you've arrived at your destination, quickly grab your stuff and leave the Little Dummy Bag mounted to your bike. You're unstoppable now. - A system of daisy chains and One-Wrap straps can be used to secure large, odd-shaped items - Interior zipper pocket - 25-lb. bag capacity. Consult your rack's weight limitations - 15L total volume

The Moloko Adjunct Personal Effects Receptacle is made from urethane-coated nylon canvas and designed to fit in the center of the Surly Moloko Bar. It has space for essentials and can easily be accessed while riding. - Constructed from urethane-coated nylon canvas to provide water-resistant protection - Elastic cord on top snuggly secures extraneous loose items like wrappers or gloves - Integrated light port allows a battery cord to pass through - Dimensions: 254 x 90 x 90mm

Designed to pair with the Surly 8-Pack Rack and similar porteur-style front racks, the Petite Porteur House Bag attaches easily via three adjustable straps. Featuring a refined pocket strategy, a classic roll top and structured body for added stability, and a bunch of webbing loops for attaching lights and lashing straps, there’s nothing petite about the possibilities here. - Includes two One-Wrap straps and one accessory bungee for securing loads of different shapes and sizes - Large main compartment, one large front pocket, and two smaller pockets in back - 25-lb. bag capacity. Consult your rack’s weight limitations - Dimensions when Rolled: 275 x 190 x 240mm - Dimensions when Unrolled: 275 x 190 x 400mm - Main body 1680D nylon, Liner 400D nylon. Bag fabric and hardware are bluesign Approved, which means the materials are sustainably produced to have the lowest possible impact on people and the environment - 11L volume Specifications: - Number of Compartments: 5 - Access Style: Roll Top - Primary Material: 1680D Nylon with polyurethane coating - Waterproof: No